How To Make A Sword Scabbard
- Home
- Customization Tutorials
- Make a Scabbard
How to Brand a Scabbard the Easy Mode
It may exist a relatively easy mode to make a scabbard, merely THIS is the end result
This guide on how to brand a scabbard for a medieval sword has been edited and condensed from a work in progress thread on the SBG Sword Forum past Lukas MG (ChenessFan).
You lot tin use the template and ideas to make a scabbard of your ain by but modifying any of the steps to suit your design and private mode. While information technology is a lot of work, and your first attempts may not turn out exactly as you might want them to, the key to becoming a good scabbard maker is practice, practice, practice.
As carving out a scabbard is very time consuming, Lukas uses a method that uses sparse wooden slats bent to form the scabbard core.
For this project, the post-obit materials were used:
- 1mm maple slats
- lightly oiled goat fur for the lining to protect the blade from scratches, keep it oiled and stop it from easily falling out (hairs should face up the scabbard tip)
- linen and rabbit peel gum (or PVA agglutinative) to demark it together
- thin leather sheet to wrap effectually the wood core
To begin with, the shape of the scabbard was traced out on the maple slats and goat fur glued to i side to form the lining.
As the cadre isn't glued together merely held solely by the linen wrap, at that place is no need to leave much room on either side of the bract'due south edge, (2mm were plenty). This makes for a core that follows the blade shape very closely and adds little bulk.
The 1mm maple slats are very flexible and tin blot shock quite well, a good affair should the scabbard ever run across stress (falling on, etc - pictured right demonstrating its flexibility).
The combination of fur on the inside and linen plus leather on the outside makes for a very light all the same durable structure. With the hide gum soaking through linen and forest and irreversibly combining them it's really kind of a medieval composite material.
Later both slats were formed, wrap them with tape or cord and insert the sword, leaving it at that place for a few days or up to a calendar week - using a thicker dummy sword if necessary if it is still a bit too tight (this dummy can and should besides be used in the next steps to ensure information technology does not tighten upwards at whatsoever stage during the scabbard making process).
To prevent bang-up, it is non a bad idea to wet the slats before hand - in this case it was non washed because Lukas received the slats pre-glued with the goat fur, just if he had not, it would have been better to wet the slats so that they bend easier.
The side by side step is a rather messy 1 - and involves using heated rabbit skin glue which when dry out is both hard and flexible.
The glue sticks to everything, especially fingers it seems. It is also just usable when heated to a honey like consistence and one needs to piece of work rather quickly before information technology cools down besides much. Once dry out information technology forms an extremely stiff spring, one that cannot easily be broken past hand and can be ground and sanded similar modern epoxy.
Next, the scabbard mouth is reinforced with a thick slice of leather and a central riser also glued into place, hibernate glue and a linen strip turning everything into one single piece.
Afterwards letting the glue dry for a day, sand the cadre downwards until it is nice and even.
Afterwards, the core was wrapped with wet leather and glued down into place rather than stitched. There is historical evidence that both methods were used to make a scabbard, and of course, information technology is much easier to glue information technology down rather than spend hours stitching the thing.
And that pretty much is how information technology is done - y'all tin brand or buy a steel throat and chape (make them past soldering two sheets of 1mm sheet steel together) for the scabbard and even go so far equally to make a chugalug like Lukas did or carve some patterns or pattern elements into it - its upwards to you!
Nigh the Artisan - Lukas MG
A sword enthusiast who never out grew his boyhood involvement in swords, with the assistance of the SBG Sword Forum over the years Lukas Mästle-Goer has become a talented sword maker in his own right and now makes and modifies swords part time from his home workshop in Deutschland.
http://www.lukasmaestlegoer.com/
I promise this information on how to make a scabbard has been helpful. To return to Free Sword Customization Tutorials from How to Make a Scabbard the Easy Way, click hither
Buying Swords Online Can Be Unsafe!
Find the Best Swords in the:
Pop & Recommended ARTICLES
Source: https://www.sword-buyers-guide.com/make-a-scabbard.html
0 Response to "How To Make A Sword Scabbard"
Post a Comment